After customers purchase finished belt, custody of the belt may not understand. Xi Lu Ning County plant chain network technicians tell you how to mesh belt for safekeeping. Belt at the factory are coated with an appropriate amount of anti-rust oil and rust-proof paper packaging, as long as the packaging is not damaged long urban network with quality belt will be guaranteed. However, long-term storage, the humidity should be below 65% and a temperature at 20 degrees Celsius, and stored on a shelf 30cm above the ground is appropriate. In addition, should keep away from direct sunlight or contact with the cold wall. 1) Prepare the network with the installation of the network with pre-installation considerations bearing due to rust after treatment and packaging, and therefore can not not open the package just before installation. In addition, the mesh belt coated with anti-rust oil with good lubricating properties, for filling grease belt or belt general-purpose, can be used directly without washing. But for the instrument with webbing or for high-speed rotation, application of clean rust oil cleaning oil will wash away, then network with easy to rust, can not place a long time. Removing network with periodic inspection or replacement parts mesh belt conveyor belt need to be demolished. Typically shaft and continue to use almost every belt, belt also tend to continue to use. Therefore, the structural design must take into account the disassembly of bearings, not to damage the mesh belt, mesh belt and other parts, but also to prepare the appropriate removal tool. When removing the static with the ring, only added to the tension on the collar, not pulling through the rolling rings. Choose stainless steel products should know the identification of the stainless steel chain network Ning 西卢 factory specializes in the production of stainless steel mesh, stainless steel chain, stainless steel chain plates, as well as related products. 1, chromium, nickel-chromium-nickel composition of two elements matching stainless steel, is a good stainless steel. Adding a lot of nickel in stainless steel in order to obtain such a single austenite, thereby improving the corrosion resistance and manufacturability. At room temperature and low temperature ductility and toughness strong, non-magnetic stainless steel mesh belt dryer with between good resistance to intergranular corrosion. (1) The corrosion resistance of chromium stainless steel Chromium plays a major role is to determine the corrosion resistance of stainless steel can of the main elements, because the steel contains chromium passivation phenomenon can make the stainless steel in an oxidizing medium, i.e., the surface to form a thin membrane, the membrane enriched in this layer of chromium. The higher the chromium content in steel, corrosion resistance is stronger. In addition, chromium on mechanical and technological properties of steel reinforcement can play a good role. (2) the impact of nickel for stainless steel only when it can be fully manifested chromium complexes. Nickel alloy elements form austenite, when used in conjunction with nickel and chrome, you can make from a single-phase microstructure of ferrite to austenite and ferrite phase structure, heat treatment, can improve the strength mesh belt, so that it has a stronger stainless steel corrosion resistance and good deformation properties. 2, the impact of impurities on the performance when the carbon content is between 0.1% to 0.3%, after annealing, the carbon will be in the state between graphite lattice boundary precipitates, destroyed the binding force between grains strongly reduce the strength and ductility of nickel, the processing deformation difficult. Further carbon and chromium has a strong affinity, capable of forming a series of carbide. The higher the carbon content of steel, chromium carbide formation of the more solid solution containing chromium content is relatively reduced corrosion resistance of steel can be reduced. Sulfur is harmful impurities, the sulfur compound and nickel is formed Ni3S2, Ni3S2 and nickel at 625 ° C formed a low melting point eutectic, distributed on the grain boundaries, when the heat distortion temperature than the eutectic melting point, i.e., cracking along grain boundaries to produce the so-called 'hot crisp' phenomenon. Nickel at normal temperature and sulfur generated Ni3S2 can cause cold and brittle. Mesh belt conveyor belt _ _ Urumqi 西卢 chain network plant provided by Ning County 西卢 chain network plant. Ning County 西卢 chain network Factory (www.njxllw.cn) strong, credible, in Dezhou chains, sprockets and other industry has accumulated a large number of loyal customers. The company better work attitude and constantly improving innovative ideas will lead Xi Lu chain mesh factory and you hand into the brilliant, for a better future!